Abarth
Alfa Romeo
Asia Motors
Aston Martin
Audi
Austin
Austin-Healey
Bentley
BMW
Chevrolet
Chrysler
Citroen
Daewoo
Daihatsu
Daimler
DMC
Dodge
Ferrari
Fiat
Ford
Ginetta
Hillman
Holden
Honda
Hummer
Hyundai
Indigo
Infiniti
Isuzu
Jaguar
Jeep
Jensen
Kia
Lancia
Land Rover
LDV
Lexus
Lotus
Mahindra
Maserati
Mazda
Mercedes-Benz
MG
Mini
Mitsubishi
Morris
Nissan
Noble
Opel
Peugeot
Porsche
Proton
Reliant
Renault
Rootes Group
Rover
Saab
Seat
Singer
Skoda
Smart
Ssangyong
Subaru
Sunbeam
Suzuki
Talbot
Tata
Tesla
Toyota
Triumph
TVR
Vauxhall
Volkswagen
Volvo
Reduce Tyre Wear
SuperPro Easy-Lift Kit
TRC096LK
This kit will lift the vehicle approx. 45mm and retains the standard suspension. Kit contains 2 Front Strut Spacers, 2 Rear Raising Blocks, 4 U Bolts & Brake Hose Extension Kit
Strut Top Spacer Kit
TRC008-6
Spacer Sleeve, suspension strut mount.
Raises vehicle approximately 10-12mm.
Raises vehicle approximately 10-12mm.
Quantity required: 1
Fitment Difficulty:
Fitting Time: 3hrs 30mins
Wheel-alignment required after fitment
33mm Heavy Duty 2-Position Blade Adjustable Anti-Roll Bar
RC0016FZ-33
Supplied with Anti-Roll Bar Mount Bushes
4
Anti-Roll Bar Mount Bushing Kit
7
Control Arm Upper Complete Assembly
Standard Alignment
TRC477
Standard replacement for non-lifted vehicles. Comes complete with standard alignment SuperPro bushes and standard ball joints.
Quantity required: 1
Fitment Difficulty:
Fitting Time: 1hr 30mins
Wheel-alignment required after fitment
Fixed Offset
TRC6470
Left and Right Offset Arms for Lifted Vehicles with Fixed Caster and Camber Correction.
These arms fitted with Heavy Ball joints and SuperPro Bushes to reduce Arm movement.
Getting the correct alignment is no longer a problem.
The SuperPro Fixed Offset Upper Control Arm is an all-in-one solution for any vehicle that has been lifted between 40mm and 65mm (2.5?). Providing an increase between 2.5 and 3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off a 50mm Lift) along with greater clearance to the coil over strut and more articulation of the arm.
These arms fitted with Heavy Ball joints and SuperPro Bushes to reduce Arm movement.
Getting the correct alignment is no longer a problem.
The SuperPro Fixed Offset Upper Control Arm is an all-in-one solution for any vehicle that has been lifted between 40mm and 65mm (2.5?). Providing an increase between 2.5 and 3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off a 50mm Lift) along with greater clearance to the coil over strut and more articulation of the arm.
Quantity required: 1
Fitment Difficulty:
Fitting Time: 3hrs
Wheel-alignment required after fitment
Ball Joint Upper Boot Kit
TRC7000RK
Kit includes Boot and Circlips for one control arm. Fits TRC470
Quantity required: 2
Fitment Difficulty:
Fitting Time: 30mins
Wheel-alignment required after fitment
Control Arm Lower Camber Bolt Kit
TRC0019
Complete set of replacement camber bolts
Quantity required: 1
Kit Includes: 4 x Bolts, 4 x Nuts, 4 x Washers
Fitment Difficulty:
Fitting Time: 2hrs
Wheel-alignment required after fitment
10
Control Arm Upper-Inner Bushing
Offset Kit for Camber Adjustment
SPF3230K
Offset Tube for Camber Decrease on raised vehicles - Remove original shell for fitment
Quantity required: 1
Kit Includes: 4 x Polyurethane Bushes, 4 x Steel Tubes, 1 x Instruction Sheet, 4 x Washer(s) - used for Steel and / or Polyurethane
Shock Absorber Lower Bushing
SPF2348PK
Spring Front Eye Bush
SPF2670K
Spring Rear Eye Bush
SPF2671K
Spring Shackle Upper Bush
SPF2672K